Exactly How to Install a Bath Tub Yourself
Exactly How to Install a Bath Tub Yourself
Blog Article
Just about every person is bound to have their own theory about Installing A Bathtub.
Setting up a bath tub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old bathtub is readily available, the job can relocate speedily; if you have to open a wall surface to eliminate the old tub as well as position the brand-new bathtub, the job is much harder. In either situation, the project is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and also set in the new one. Make sure you have actually qualified on your own for the work and also fit attempting it. Rather than employing a specialist to take control of a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you install a new bathtub in your restroom if you have already bought a new tub and also do not require to transform the setup of your previous water pipelines.
Your devices and product list ought to comprise the following:
Getting ready for the Setup
First of all, the supporting frame supplied with the bath needs to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to stop stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic because of the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of both wooden boards under its feet, put the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the tub up until the level reviews level.
To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system and also examine all joints and also brand-new pipework for leakages and tighten them if necessary. Fill up the tub as well as likewise check the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, fix the bath paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub ought to wait until the bathtub has been used at least when as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location between the tap and the sink. Protect the tap in place with the manufacturer given backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, causing the water to pass through the wall between the bathroom as well as the tiling, resulting in difficulties with wetness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and also cartridges, and also can securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the tub with water prior to securing, to allow for the activity experienced when the tub is in use. The sealant can crack fairly very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily available on the marketplace. It is suggested to fit the ceramic tiles making use of waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was guided to that article on How to Install a Bathtub Yourself through a good friend on another web page. Sharing is nice. You won't know, you might be helping someone out. I treasure reading our article about How to Install a Bathtub Yourself.
Free Estimate
Report this page